Home > Sterilizers > RapidHeat Sterilizers >

RapidHeat RH-Pro9 High Velocity Hot Air Sterilizer

MADE IN THE USA

Availability: In Stock
Product Code: NRH-PRO9

Description

Technical Specs

Literature

RapidHeat RH-Pro9 High Velocity Hot Air Sterilizer with 3 trays, 110-120V electrical by CPAC - The perfect replacement for the now discontinued Dentronix Sterilizer. Accommodates Dentronix plier racks!

WARRANTY: 3 years, parts and labor
Chamber air circulates at over 200 times per minute! Watch how it works in Video tab.

The Industry’s Most Efficient Sterilizer (now in a convenient cabinet-ready size)
Chamber air circulates at over 200 times per minute!

The RH-Pro family is a proven advancement in “RapidCycle” sterilization. Our RH-Pro11 tabletop sterilizer has been raising sterilization efficiency levels since its release. Now, we have taken that cutting edge technology and made it small enough to fit inside a cabinet! The RH-Pro9, like our larger RH-Pro11, uses Cutting-Edge HVHA (High-Velocity Hot Air) technology to provide the fastest instrument turnaround of any FDA-Cleared sterilization technology. No steam or water means no lengthy drying cycle with longer instrument life free of corrosion.

For Healthcare, the RH-Pro9 can Eliminate Immediate-Use Steam Sterilization, shortened cycles, work-arounds, and Joint Commission scrutiny!

The RH-Pro9 Advantage

FDA-Cleared 6 Minute Cycles (Unwrapped)
FDA-Cleared 12 Minute Cycles (Wrapped)
Smaller Cabinet-Ready Size (1163 Cubic Inches)
Uses 85% Less Energy Than Steam
Non-Corrosive Sterilizer Environment
Full 3-Year Warranty
Waterless Sterilization with No Chemicals
Convenient Smaller Size -- Three Instrument Trays
Available in 2 sizes:
- RH-Pro9 - 3 trays / chamber: 9.5”W x 15.6”D x 7.85”H
- RH-Pro11 - 4 trays / chamber: 11”W x 17.75”D x 11.75”H

Compare RapidHeat vs. Steam Sterilization

Sterilizer Feature	RapidHeat	Steam
Start to Finished Sterilization Cycle	12-20 minutes	61-116 minutes
Sterilizer Operation	Simple	Complex
Water Requirements	None	Distilled Water
FDA 510(k) Cleared	Yes	Yes
Cycle Documentation	Yes	Yes
Instrument Drying Cycle	None	FDA Required
Potential for Instrument Corrosion	None	High
Energy Use (kWh/cycle)	$0.11/cycle	$0.74/cycle
Maintenance and Repair Cost	$0.80/cycle	$6.00/cycle

Notes:
Start to finish cycle represents the time range for sterilizing unwrapped, pouched and wrapped (cassette/tray) instruments from cold start to finish (includes dry cycle for steam).
Sterilizer Operation reflects the level of sterilizer preparation and management for instrument processing.
Potential for instrument Corrosion is absent in the dry environment pf a RapidHeat sterilizer and high for instruments in a steam environment.
Energy Use represents kilowatts of power used per hour when operating a sterilizer cycle. This study was conducted by the Rochester Institute of Technolofy comparing RapidHeat to 2 popular tabletop steam sterilizers.
Maintenance and Repair Cost is based on actual reported costs and estimated over useful life.

Features

Q. Can I use the same pouches for this sterilizer I use with my autoclave?
A. No, because RapidHeat sterilizers run up to 375 degrees; and most pouches made for steam sterilization cannot withstand that heat.

Q. We were of the understanding that we could put instruments in wet. Can you confirm that?
A. All instruments must by DRY when put into rapidheat sterilizers. Any liquid will produce steam inside the chamber. View How to Prepare Instruments for RapidHeat Sterilization for detailed instructions and tips from the manufacturer.

Q: Can I continue to use our old Dentronix plier racks in the Rh-Pro?
A: Yes – you can! See the IFU here.